Airborne Systems
Recorders
MITR 5510 - Modular Instrumentation TAP & Recorder
The Modular Instrumentation TAP Recorder (MITR) is a high-bandwidth, high-capacity IRIG 106 Chapter 10 data recorder/ publisher with a TAP Interface Module (TIM) & multiple Tera-Bytes of high-speed removable storage. MITR is suitable for a wide range of data recording requirements in harsh & demanding environments.
MITR 5510’s configurable TIM provides protocol independent full duplex optical transceivers. Applications include GigE, Fibre Channel, AS5643 IEEE-1394B (Firewire), or any specific communication application. Input channels are recorded/ published while mirrored outputs provide full active TAP capabilities. TAP components are powered via primary or auxiliary 28VDC.
MITR 5520 - Copper Fibre Channel TAP & Recorder
The Modular Instrumentation TAP Recorder (MITR) is a high-bandwidth, high-capacity IRIG 106 Chapter 10 data recorder/ publisher with a TAP Interface Module (TIM) & multiple Tera-Bytes of high-speed removable storage. MITR is suitable for a wide range of data recording requirements in harsh & demanding environments.
MITR 5520 TAP Interface Module (TIM) provides up to 8 channels of 1G copper Fibre Channel using Quadrax connectors . Input channels can be filtered, recorded and published while mirrored outputs provide full active TAP capabilities. TAP components are powered via primary or auxiliary 28VDC.
MITR 5530
The Modular Instrumentation TAP Recorder (MITR) 5530:
✓ Up to 64TB RMM
✓ Option to Use GFE DRMM
✓ Same Management capabilities 5510/20 MITR
✓Additional CH7/HDLC PCM Output
• 12 Optical TAPs 1-10G
• Data Protocols
✓Fibre Channel & Ethernet
✓ARINC-818, sFPDP, 1394 and more!
• 8 PCM, 8 Video, 8 1553, 2 Audio, 1 Video Out
• Higher Throughput - Up to 64Gbps (8GBps) Sustained Record Rate
• USAF F15EX Fleet Recorder
Switches
iES-6
The iES-6 integrated Ethernet Switch, is a rugged 6 port layer 2/3 managed gigabit Ethernet switch with end node timing & discrete signal capabilities for demanding test instrumentation environments on airborne, shipboard or mobile ground vehicles. Programmable discrete outputs can be used to control end node devices, on or off the network, as well as feedback into the iES-6 from discrete inputs. iES-6 contains a hardware based IEEE-1588v2 time engine with (4) independent clocks which can be setup as ordinary, boundary, peer to peer transparent or end to end transparent, master only, slave only & one or two step clock.
iES-12
The iES-12 integrated Ethernet Switch, is a rugged 12 port layer 2/3 managed gigabit Ethernet switch with end node timing and discrete signal capabilities for demanding environments on airborne, shipboard & ground vehicles. Switch traffic filtering capabilities include; Port User Limit Control, VLAN/ MAC Address (Static MAC Table), Packet/Bit Rate Limiters, Port Based and Frame Type and IP Filtering (ACL, Static/Dynamic Multicast). Audio Video Bridging (AVB) capability is also supported. A programmable FPGA tied directly into the switch with two 1G interfaces provides line-rate packet processing capabilities.
iES-16
The iES-12 integrated Ethernet Switch, is a rugged 12 port layer 2/3 managed gigabit Ethernet switch with end node timing and discrete signal capabilities for demanding environments on airborne, shipboard & ground vehicles. Switch traffic filtering capabilities include; Port User Limit Control, VLAN/ MAC Address (Static MAC Table), Packet/Bit Rate Limiters, Port Based and Frame Type and IP Filtering (ACL, Static/Dynamic Multicast). Audio Video Bridging (AVB) capability is also supported. A programmable FPGA tied directly into the switch with two 1G interfaces provides line-rate packet processing capabilities.
TAPs and Gateways
RTAG
As an extension of the MITR, RTAG shares most of the design, logic and firmware with the MITR’s TAP & Interface Module (TIM). The RTAG provides multiple TAPs for optical & copper links in many formats (Ethernet, Fibre Channel, ARINC 818 & IEEE-1394/AS5643) and is available in several configurations: A 1G Optical (Ethernet & Fibre Channel) with 8 channels of Tx/Rx TAP’s & 8 channels Tx outputs, a mixed 1G Copper & 1G Optical (Fibre Channel) with 4 channels Tx/Rx TAP’s & 4 channels Tx outputs and a 10G Optical (Ethernet) with 8 channels Tx/Rx TAP’s & 8 channel Tx outputs.
iGU - Instrumentation Gateway
Configurable gateway between instrumentation systems, Ethernet networks and telemetry transmitters. Contains a layer 2/3 managed switch, FPGA & quad-core ARM CPU for data processing & protocol transforms.
Features
• Ethernet Switch with PCM Inputs/Outputs
• IRIG 106 Chapter 7/HDLC Encoder & Decoder
• Any Ethernet to Chapter 7/HDLC PCM Output
• Chapter 7/HDLC PCM Input to Ethernet
• Any Ethernet to Chapter 10